chat
send private message
Drizztbenre
joined nov 2023
share Drizztbenre and generate bitcoin with reference codes.
1 topic on Drizztbenre
+1
Drizztbenre
How to fix LR crystallization for carts??
Hi all, need some advice if possible.
I received a good amount of Live Resin for dispos, but it seems hard to handle and even after filling a cart,the LR crystalizes, even though it can be vaped. Should I decarb it some more in the oven to get it more thin to use in my other carts? If so, at what temp? Quantity of 40g approx.
I'm not looking to mix it with D9.
I've also read about a
the flavourless Terpene Diluent - Viscosity Agent, that can do that job with a few drops if anyone knows more about it.
I do not own any special heating devices etc. I'm also thinking of buying a heated cart filling gun machine.
Thank you in advance.
+3
DiamondExtracts
All replies telling you to heat it are wrong.

That simply won't work, by the time you heat the cart up, anything that is liquid will leak. You cannot heat the carts up too hot otherwise the contents are forced out the bottom.

What you need to do in future is decarb the live resin, there are various ways to remove terps from the extract first before decarbing, but you have to be careful NOT to include any of the extract and ONLY there terps.

If there is any crystals in the terps you remove, it will re-seed the extract and it will crystalize again.

You can use a 100% live resin mix in your cart after decarbing, but it's advised to add 20-30% distillate, otherwise the cart will likely clog before you finish it.

You'll also need to re-add terps as the flavour will be lacking if you didn't remove the terps before decarbing.

I wouldn't use some random diluent off the internet, lots of those have very very nasty shit in including some of the top websites everyone mentions on here constantly.

I also can't advise anywhere to buy them as I don't know any legit sources, so I'm sorry about that. Good luck with the carts.

And one more thing, make sure that before you add the decarbed extract+dist to carts that it doesn't FIZZ up. If it's not decarbed properly, then the extract will fizz up when it's heated up/cooled off in the cart. This can ruin your entire batch of carts.

DO NOT BUY A HEATED CART FILLER. They are fiddly, expensive and a waste of time. You'd be better off filling with a syringe. The guns never fill the carts up to the top and you end up spilling it constantly, because if you pull all the liquid up into it and there is a small bubble in the syringe, it will drip and leak constantly, covering your carts. Dont even bother, mine went straight in the bin after one use.
+2
Drizztbenre
Thank you very much for the comment and all the info you mentioned brother.
I will decarb it, but only thing I didn't get is the part of seperating the terps from the Live Resin sauce, shouldn't just decarb it with low temp and keep the lid closed in order not to lose those terps? From videos I've seen, after decarbing it right it should be fluid enough to handle and fill in the carts.
+2
Classygrass1
I'd write that cart off personally - especially if you've got 40g.

Look up jartek decarb, get a hotplate stirrer.

I would not recommend trying to decarb all at once as it's easy to over do and you'll lose those precious terps.

Also stay well clear of any terpene diluent, if you're making pure live resin carts the only thing in that cart should be decarbed live resin.

If you need to thin it out use real canna derived terps and or CBC Distillate.
+1
Drizztbenre
Thank u very much for your comment brother. I made a bit of research and I m gonna use jartek. hotplate stirrer is to place the jar after I finish with the oven right?
Would you have any suggestions on the time/temp needed? I'd prefer doing all 40g at once but since I m a newbie in this I should better make at least 2 batches.
Comments state that I should seperate the terps from my live resin sauce before decarbing it is that right?
+2
Classygrass1
No problem bud.

I use a hotplate to decarb instead of oven but honestly I don't think the heating source makes all the difference.

It's about temp and time.

Start around 90c for 1.5hrs using a small amount - 5g

The best way i believe is to use a centrifuge to mechanically separate the hte from the thca, then decarb only the thca. After that add the hte back and fill carts.

Check out 'howtoweed' on YouTube, all explained on there.
+2
Jester
You need to pop the cap off and warm the extract enough for it to come out and then decarb it properly. Don't try to heat the cart itself, the pressure from heating the extract will cause it to leak. Howtoweed on YouTube has a guide to extract from carts I think.
Need to be careful though, if it's a pop cap and not a screw, if you apply too much pressure the glass will shatter.
+2
Wambamthankyoumam1
Needs more decarbing if it's doing that
+1
MightyRux
Can you put it in something waterproof and warm it up a bit in warm water? I've never encountered this before, sorry. Just a suggestion.
4 posts by Drizztbenre
WHAT A DYNAMITE
started topic
£20 network fee?
Maybe admins should have a thought about using other coins usdt/xmr or whatsoever with less fees.. + 3 more
bigg topics